Duet 2 (USB)

Signal not showing up where it’s supposed to and routing incorrect in Pro Tools

If your signal isn’t showing up correctly in Pro Tools, coming out of Pro Tools to the desired outputs, or if the routing isn’t showing up as expected, there are a few things to check. Look below for the section that applies to the Apogee product you’re using:

 

JAM, JAM 96k, MiC, MiC 96k, Groove

  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window. If you are using JAM or MiC, you will first need to create a ‘Pro Tools Aggregate I/O’ and then you will select ‘Pro Tools Aggregate I/O’ as your ‘Playback Engine’. Click here for setting up JAM for Pro Tools.  Click here for setting up MiC for Pro Tools.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

 

ONE (every model), GiO, Duet (every model), Quartet, Ensemble (every model)

  • Confirm that you are using the correct inputs/outputs on your device. Click here for instructions on how to setup ONE.  Click here for instructions on how to setup Duet.  Click here for instructions on how to setup Quartet.
  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window.
  • Launch ‘Apogee Maestro’ and click the ‘Reset Routing’ button in both the ‘Input Routing’ and ‘Output Routing’ tabs. If you’re using an Avid Duet or Avid Quartet, you will use ‘Pro Tools I/O Control’ app instead of Maestro. Click here if you need to download the Pro Tools I/O Control app for Avid Duet or Quartet.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

Symphony I/O, Symphony I/O MkII, AD16x, DA16x, Rosetta 200, Rosetta 800

 

 

My Avid Duet isn’t showing up in Maestro

If you are using the ‘Avid Duet for Pro Tools’ (the all-black version that comes bundled with Pro Tools software), it will not show up in the ‘Apogee Maestro’ application. You will need to install the ‘Pro Tools I/O Control’ app from Avid’s website. Once you download and install this app, you should launch the ‘Pro Tools Duet Firmware Updater’ (found in Applications>Utilities>’Pro Tools Duet Firmware Updater’) and confirm that the firmware is up to date and then launch the ‘Pro Tools I/O Control’ app from your Applications folder.

Click here to find the appropriate download for either Mac or Windows. Make sure you select the download for ‘Duet’ and not ‘Quartet’.

Duet, Quartet, and Ensemble Thunderbolt’s 1/4″ and XLR inputs explained

When using Duet2, Duet for iPad & Mac, Quartet, and Ensemble Thunderbolt, it is important to remember that any of the dual XLR-1/4″ combo jacks are set up so when the input is set to ‘Mic’ or ‘Line’ (+4dBu or -10dBV), only the XLR part of the jack will receive signal. This means that you will need to use an XLR cable or a cable with an XLR adapter connected to it.

The same is true in reverse- when the input is set for ‘Instrument’, only the 1/4″ part of the jack will receive signal.  This means that you will need to use a 1/4″ cable.

 

Here are some examples for setting up different types of input sources on Duet, Quartet, and Ensemble Thunderbolt:

 

Mics

Connect your Mic using only an XLR cable (no 1/4″ adapters or cables) to the XLR input jacks on your Apogee device.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘Mic’.

If you’re using a condenser mic that requires phantom power, engage the ’48′ button on the input you’re using.

Gradually bring the input level in Maestro up until you get a good level from your input source. Make sure the meter isn’t going into the red.

 

 

Guitars, Basses, Keyboards, Hi-Z Mics that have 1/4″ cables, such as harmonica mics:

Connect your Instrument using only a 1/4″ instrument cable to the 1/4″  input jacks. (be sure that you’re connecting to the 1/4″ inputs on the combo XLR-1/4″ jacks and not the 1/4″ output jacks)

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘Instrument’.

Gradually bring the input level in Maestro up until you get a good level from your input source. Make sure the meter isn’t going into the red.

 

Sending Line-Level audio to your Apogee device and bypassing it’s mic-pres

Connect the output from your line-level piece of gear (such as a compressor or external mic-pre) to the XLR input jacks. If your Line-Level device only has 1/4″ outputs, you will need to use balanced 1/4″ to male XLR cables. You can’t use the 1/4″ input jacks on your Apogee device, as they are only used for guitars/basses/keyboards.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘+4dBu’ (for use with professional audio gear) or ‘-10dBv’ (for use with consumer audio gear).

 

What is the ‘A button’ (device ID) in Maestro for?

Most Apogee products that use the Apogee Maestro 2 control application will include a ‘Device ID’ button that can be found in multiple Maestro tabs under a graphical icon for the connected Apogee device. You will usually see this button as an ‘A’.

Here is an example of what it looks like when you have a Symphony I/O connected:

img-0

 

The purpose of this button is to quickly identify which Apogee device you’re adjusting parameters in Maestro for. When you click on the button, it will light up the front-panel of the corresponding Apogee device so you can see which device you are adjusting parameters in Maestro for. Click the button again and the device will no longer be identified.

Since multiple Apogee devices can be connected and appear in Maestro at the same time, it can sometimes be confusing to know which device you’re adjusting parameters for. Having more than one Duet or Quartet connected to a Mac may not be as common as having multiple Symphony I/Os or Ensembles connected, but the ‘Device ID’ buttons are there for each product, just in case.

 

A typical use-case:

You have 2 Symphony I/Os connected to one Mac and both are showing up in Apogee Maestro. You can go to the ‘Device Settings’ tab in Maestro and change the peripheral prefix of the 2nd Symphony I/O to ‘B’ (or any other letter you want). Now, when you click the ‘B’ button (Device ID) in Maestro, the 2nd Symphony I/O will become identified.  If you click the ‘A’ button, the 1st Symphony I/O will become identified.

 

Why are the input and output level/volume popup indicators not showing up?

Several Apogee products have pop-up level indicator graphics that will appear on the desktop of your Mac when the input and output levels are adjusted from the device or from the Mac’s keyboard volume buttons.

 

If the pop-ups aren’t appearing, there are a few things to check:

Launch ‘Apogee Maestro 2’ from your Applications folder, click on the ‘Apogee Maestro 2’ drop-down desktop menu and select ‘Preferences’. Confirm that the ‘Display pop-ups’ checkbox is checked. If you don’t see this option, then pop-ups aren’t available for the product you’re using.

 

If you’ve confirmed that the ‘Display pop-ups’ checkbox is checked and you’re still not getting the pop-ups, try the following:

 

– Unplug/replug your Apogee device

– Restart your Mac

– Launch ‘Activity Monitor’ (Applications> Utilities> ‘Activity Monitor’), click the ‘View’ drop-down desktop menu and select ‘All Processes’. Type ‘apogeepopup’ in the searchbar in the upper right-side corner of Activity Monitor. Once you see ‘ApogeePopup’ displayed in the list, highlight it and force-quit the process by clicking the ‘X’ button in the upper left-side corner of Activity Monitor. Wait a few seconds and you should see the popups again after adjusting input/output level.

 

*Note for Duet Firewire and Ensemble Firewire customers*

There was a known issue with pop-ups not working for Duet Firewire and Ensemble Firewire when using any version of Mac OS 10.8. It is recommended that you use either a version of Mac OS earlier than 10.8 or later than 10.9.

 

 

Apogee Maestro crashes when I launch it

If Apogee Maestro 2 is crashing every time you try to launch it, follow the steps below:

 

 

– Quit Apogee Maestro.

– Go to your Applications folder and locate the ‘Apogee Maestro 2’ icon.

– Click once on the icon and then hold down the Command key and press ‘i’ for ‘Get Info’.

– In the ‘Get Info’ window, check the ‘Open in 32-bit mode’ checkbox.

– Close the Get Info window and relaunch Apogee Maestro.

How do I record audio from the internet or other app using my Duet?

Using Duet to record audio from the internet or other apps
To set up your Apogee Duet for iPad & Mac or Duet 2 to record audio from your internet browser (or other app) into your DAW, follow the instructions below.

 

 

– Connect Duet to Mac.

 

– Launch ‘Apogee Maestro 2’ from your Applications folder.

 

– Go to the Input tab in Maestro. Click on the ‘Analog Level‘ drop-down menus and set each input for ‘+4dBu‘.

 

– Go to the Output tab in Maestro. Make sure both output channels are set for ‘+4dBu‘ and not ‘-10dBv’. On the right side of the output tab, make sure the speaker output is set for ‘Out 1-2‘ and not ‘Mixer’. Turn the speaker output up all the way. Make sure the speaker output is not muted or set for Dim.

 

– In the Output tab in Maestro, set the Headphone output for ‘Out 3-4‘. Turn headphones up to around -30 or -20.

 

– Connect a balanced 1/4″ TRS to Male XLR cable from ‘Out L‘ on the breakout cable to ‘Input 1‘. Connect the other balanced 1/4″ TRS to Male XLR cable from ‘Out R‘ on the breakout cable to ‘Input 2‘.

 

– Launch ‘Audio MIDI Setup’ (Applications> Utilities> ‘Audio MIDI Setup’) and select ‘Duet USB’ in the left-side device column and make sure that it’s set for the default input and output of the Mac by clicking on the drop-down menu on the bottom of the device column with the gear and arrow icons and selecting ‘Use this device for sound input’ and ‘Use this device for sound output’. Quit Audio MIDI Setup.

 

– Launch your DAW and create a new session with one stereo audio track. Go to the DAW’s Audio Preferences and make sure Duet is set for the Output and Input device and that the buffer is set for 128 or higher. Set the sample-rate to 44.1k.

 

– Set the input for your stereo track to ‘Input 1/2‘ or ‘Line 1/2‘. Set the output of the track for ‘Out 3-4‘.

 

– Record-enable the track and then launch your internet browser (or whichever app you’re trying to record from). As soon as you’re ready to start playing audio from your internet browser, get ready to record in your DAW.

 

– Hit record in Logic and start playing audio from your internet browser (or whichever app you’re trying to record from). Monitor the audio from your headphones.

Why do I only hear the left output channel when recording with ONE or Duet in Garageband?

Note- if you are experiencing audio in one output channel only when using the CAMERA APP, please click here. The article below is for GARAGEBAND.

If you’re only hearing sound from the left output channel when recording with ONE for iPad & Mac or Duet for iPad & Mac in Garageband (or other apps), this is most likely because you’re using a stereo track when you need to be using a mono track.

 

If you create a MONO track in Garagband, it will send your input out both Left & Right output channels. When you create a stereo track in Garageband, it will hard-pan both inputs, so input 1 goes out only the left and input 2 goes out only the right. This is why you’re only hearing sound in 1 channel. Stereo tracks are typically used for stereo mic situations or if a keyboard has a stereo output.

 

Here are some videos on how to set up ONE with Garageband (you can also apply these videos to Duet):

 

 

For Mac:

 

 

 

 

 

For iPad/iPhone:

 

Not getting sound/no output from Duet

Please go through these steps to ensure that everything is set up properly:

 

Setting up Duet’s inputs:

 

Mics

Connect your Mic using only an XLR cable (no 1/4″ adapters or cables) to the XLR input 1 or 2 of Duet’s breakout cable.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using for ‘Mic’.

If you’re using a condenser mic that requires phantom power, engage the ’48’ button on the input you’re using.

Gradually bring the input level in Maestro up until you get a good level from your input source. Make sure the meter isn’t going into the red.

 

Guitars, Basses, Keyboards, Hi-Z Mics that have 1/4″ cables, such as harmonica mics:
Connect your Instrument using only a 1/4″ instrument cable to the 1/4″  input 1 or 2 of Duet’s breakout cable. Make sure you’re plugging into one of the input connectors (the fat ones that are dual XLR and 1/4″) and not the 1/4″ output connectors.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘Instrument’.

Gradually bring the input level in Maestro up until you get a good level from your input source. Make sure the meter isn’t going into the red.

 

Sending Line-Level audio to Duet and bypassing Duet’s mic-pres

Connect the output from your line-level piece of gear (such as a compressor or external mic-pre) to the XLR input 1 or 2 of Duet’s breakout cable. If your device only has 1/4″ outputs, you will need to use balanced 1/4″ to male XLR cables. You can’t use the 1/4″ input jacks on Duet’s breakout cable.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using and set to ‘+4dBu’ (for use with professional audio gear) or ‘-10dBv’ (for use with consumer audio gear).

 

 

Setting up Duet’s outputs:

 

Using Duet with DAW or audio playback software:

– Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Output’ tab and set the Speaker output and Headphone output to ‘Out 1-2’ (the drop-down menus under the software output knobs)

– Confirm that the mute or dim buttons aren’t engaged in Maestro’s output tab.

 

Using Duet without any software- input directly to output:

– Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Output’ tab and set the Speaker output and Headphone output to ‘Mixer’ (the drop-down menus under the software output knobs)

– Confirm that the mute or dim buttons aren’t engaged in Maestro’s output tab.

For more on using the Maestro Mixer, see this article: Read More