MiC: Troubleshooting

How to use MiC+’s blend control

When MiC+ is plugged in and being used by an application as the microphone, the soft-key above the dial cycles through the 5 different monitoring blends.

When the left-most LED is illuminated white, this indicates full “direct’ monitoring signal. You’ll only hear what the microphone is picking up. No playback will be heard:

Continuing to press the soft-key again will cycle through the other four levels of blend. When the center LED is illuminated, you get a 50/50 equal blend of direct-monitor from the MiC+ signal, and playback:

The right-most LED illuminated white indicates full playback/software monitoring. No direct signal would be heard:

Mac Audio Optimization Guide

When streaming audio through an interface connected to your Mac, there are many factors that can cause performance problem:

  • audio artifacts such as pops or clicks, stutters, or dropouts as you play or record
  • erroneous firmware messages, performance issues, or other strange behavior.

Use this guide to optimize your Mac computer to reduce the chances of this from happening, or as a starter if you have any issues.

Please keep in mind these steps are not required to use our product, but have solved problems for customers in the past. It is best to test these known fixes first and see if they relate to your issue.

Turn off Automatic Sleep Mode

In Apple Menu > System Preferences > Energy Saver set Computer Sleep to Never.
Make sure “Put hard disks to sleep when possible” is NOT checked.
(These settings may vary on different Mac Models)

This will mean that Sleep Mode does not come on automatically, but you can still put your computer to Sleep when you like, by going to Apple Menu > Sleep.

This is one of the most important steps to prevent problem behavior with an audio device because Sleep Mode works by suspending drivers in a hibernate state, rather than unloading them fully. When waking up the computer does not “enumerate” the drivers fresh as with a newly connected device, but just attempts to proceed as if nothing changed.

However your Audio Device will think it has been disconnected during Sleep, as the driver was no longer available. During Sleep the unit may shut off or go into a standalone mode depending on it’s model/design/features. When the computer wakes from Sleep the Audio Device doesn’t receive a good connection because the driver is not reloaded fresh as with a true unplug/replug, called “driver enumeration.”

Automatic Sleep can lead to situations where you get up for a quick break during your session and come back to glitchy audio, artifacts, no audio, a full disconnect, and other performance issues. Very short Sleep Mode settings, such as every 1 minute, can even create situations where you turn to do something in the studio like adjust your outboard mixer and before you are done the whole unit has been disconnected, or an erroneous firmware message has popped up.

If you must use Sleep Mode, then for best performance first turn off/unplug your interface and then choose Sleep from the Apple Menu. When you come back to work you can Wake the computer and then plug in/power the interface and get a freshly loaded driver.

Remove or Disable Unused Network Adapters

In Apple Menu > System Preferences > Network and make sure to remove any Network Adapters you are not currently using for a LAN or Internet Connection.

For example remove “Bluetooth PAN” “Thunderbolt Bridge” “Firewire” et al.

Having a port that shares a USB, Firewire or Thunderbolt Bus with your Audio Hardware here can limit its bandwidth.

When a certain Port Type, for example “BlueTooth PAN” is listed here, but not in use the computer will constantly “ping” that Port, looking for a connection to appear. This can create a lot of Network Traffic where it isn’t needed, such as on your USB Bus, since BlueTooth is an internally connected USB Device. This can lead to those constant pings knocking your audio device off the USB Bus, disconnecting it.

Turn off your Firewall

In Apple Menu > System Preferences > Security & Privacy > Firewall make sure Firewall is Off.

Networkingis one of the most common sources of audio problems on all computers, Mac and PC. This could be Network Activity on the computer, but also Firewalls for specific programs or computer blocking connections. In general it is best to disable the Firewall on any Audio Production computer.

If you do have important Firewall tasks that need to be done, like opening a Port Forward for your Video Games, it is best to do this on your Router instead, as that device is better equipped. It won’t cause so many audio interactions when done on a different device.

Remove Startup Items

In Apple Menu > System Preferences > Users & Groups > Admin Account > Login Items: remove any Startup items.

Startup Items can be control panels for other audio gear, like Digidesign loader, or programs like Spotify that go online and can interrupt other audio programs. Also things like Adobe Creative Cloud, or even Anti Virus Software will run in the background and slow down your computer.

In this screenshot you can see the computers has iTunes, Flux a color temperature program, and Dropbox all starting up when the computer loads. As iTunes and Dropbox can go online in the background, and Flux may affect graphics performance, these could all potentially affect audio or CPU performance negatively. It is best to remove them if having audio troubles.

There are no Startup Items by default on the Mac so you can remove all of them with no issue.  If you are worried about removing some items, then take a screenshot of them so you can restore them at a later time: https://support.apple.com/en-us/HT201361

Repair Disk Permissions

In Applications > Utilities > Disk Utility: select Macintosh HD and click First Aid (Repair Disk Permissions on older Macs). Repeat this for any other Hard Drives you have connected.

Choose your best USB or Thunderbolt Port and cable

If you are using a USB Audio Interface (such as Duet), try all the USB ports on your computer. One may work better than another due to how the internal ports are hubbed.

Be sure you have tried another USB, Thunderbolt or Firewire Cable.

Turn off Analytics and Location Services

In System Preferences > Security & Privacy > Privacy Tab > Analytics (could say Diagnostics and Usage), un-check the boxes for Share Mac Analytics, Share with App Developers, and Share iCloud Analytics.

You may also want to disable Locations services found in this same Privacy Tab to further reduce background network traffic.

Turn off Sound Notifications for Apps

Turn off sound notifications for all your apps: In System Preferences > Notifications, select an app then un-check the box for “play sound for notifications. Repeat this for all apps in the left side-bar.

After these steps please RESTART the Computer

While you are Recording

  • Check that any Virus Scanners or Backup software (i.e. Hightail or Carbonite) that run in the background are disabled.  High background activity especially over the Network can cause glitches.
  • Close any unnecessary applications while recording (i.e. Skype or Browsers you are not actively using.)

Do Apogee USB products (Groove, ONE, Duet, GiO, MiC, JAM, Quartet) work with the latest MacBook?

Question:

Do Apogee’s current USB products (Groove, ONE for Mac, ONE for iPad & Mac, Duet 2, Duet for iPad & Mac, GiO, MiC, MiC 96k, JAM, JAM 96k, Quartet) work with the 2015/2016 12″ MacBook?

 

Answer:

Yes. The 2015/2016 12″ MacBook includes a USB-C port. Since USB-C uses a different size port and connector than traditional USB ‘Type A’, you will need to use an Apple USB-C to USB adapter to connect any USB device with a traditional ‘Type A’ connection, such as Apogee’s line of USB audio interfaces, to this port.

Apogee’s line of USB audio interfaces are also fully compatible with the 2016 MacBook Pro, as outlined in this post.

 

*It should be noted that Apogee’s Thunderbolt products will NOT work with the 2015/2016 12″ MacBook.

 

Click for information about compatibility with Apogee’s Thunderbolt products and the 2015/2016 12″ MacBook.

Click for information about compatibility with Apogee’s Thunderbolt products and the 2016 MacBook Pro.

Click for more information on the differences between USB-C ports and Thunderbolt 3 ports.

 

 

 

 

Do Apogee USB products (Groove, ONE, Duet, GiO, MiC, JAM, Quartet) work with the 2016 MacBook Pro?

Question:

Do Apogee’s current USB products (Groove, ONE for Mac, ONE for iPad & Mac, Duet 2, Duet for iPad & Mac, GiO, MiC, MiC 96k, JAM, JAM 96k, Quartet) work with the 2016 MacBook Pro?

 

Answer:

Yes. The 2016 MacBook Pro with Touch Bar includes Thunderbolt 3 ports, which can also be used to connect USB devices. Since Thunderbolt 3 and USB-C use the same size ports and cables, you will need to use an Apple USB-C to USB adapter to connect any USB device with a traditional ‘Type A’ connection, such as Apogee’s line of USB audio interfaces, to these ports.

Apogee’s line of USB audio interfaces are also fully compatible with the 2015/2016 12″ MacBook, as outlined in this post.

 

*It should be noted that Apogee’s Thunderbolt products will NOT work with the 2015/2016 12″ MacBook.

 

Click for information about compatibility with Apogee’s Thunderbolt products and the 2016 MacBook Pro.

Click for information about compatibility with Apogee’s Thunderbolt products and the 2015/2016 12″ MacBook.

Click for more information on the differences between USB-C ports and Thunderbolt 3 ports.

Signal not showing up where it’s supposed to and routing incorrect in Pro Tools

If your signal isn’t showing up correctly in Pro Tools, coming out of Pro Tools to the desired outputs, or if the routing isn’t showing up as expected, there are a few things to check. Look below for the section that applies to the Apogee product you’re using:

 

JAM, JAM 96k, MiC, MiC 96k, Groove

  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window. If you are using JAM or MiC, you will first need to create a ‘Pro Tools Aggregate I/O’ and then you will select ‘Pro Tools Aggregate I/O’ as your ‘Playback Engine’. Click here for setting up JAM for Pro Tools.  Click here for setting up MiC for Pro Tools.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

 

ONE (every model), GiO, Duet (every model), Quartet, Ensemble (every model)

  • Confirm that you are using the correct inputs/outputs on your device. Click here for instructions on how to setup ONE.  Click here for instructions on how to setup Duet.  Click here for instructions on how to setup Quartet.
  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window.
  • Launch ‘Apogee Maestro’ and click the ‘Reset Routing’ button in both the ‘Input Routing’ and ‘Output Routing’ tabs. If you’re using an Avid Duet or Avid Quartet, you will use ‘Pro Tools I/O Control’ app instead of Maestro. Click here if you need to download the Pro Tools I/O Control app for Avid Duet or Quartet.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

Symphony I/O, Symphony I/O MkII, AD16x, DA16x, Rosetta 200, Rosetta 800

 

 

What happens when I receive a call while recording with my Apogee interface?

Monitoring and recording is interrupted in Apple GarageBand and other Audio Apps from the ONE for iPad & Mac, Duet for iPad & Mac, Quartet, JAM, JAM96k, MiC, or MiC96k when a call is received. Once the call has ended or declined monitoring and recording is resumed.

Unless calls are more important than creativity? It is recommended that in the iPhone> Settings Do Not Disturb is turned On. This will prevent a call from interrupting that perfect take or inspired performance.

iPhone Settings

The iOS cable won’t stay connected to my iPhone or iPad

If you have a case on your iPhone or iPad, it may be obstructing the iOS connector from being inserted into the jack all the way. Please remove the case or cover to verify if this is the cause.

If you do not have a case or cover on your iPhone or iPad and the cable won’t stay connected, then there may be a problem with the iPhone or iPad, the Apogee product, or the cable. Please contact the Apogee Support Department to further troubleshoot the issue.

http://www.apogeedigital.com/support/contact-support

No input in Auria

If you are not able to get input in to Auria, follow these steps:

 

– On your iDevice, go to ‘Settings’.

– In the Settings page, go to ‘Privacy’.

– Select ‘Microphone’.

– Find Auria in the list and enable the switch next to it.

 

 

 

How to hear input in Garageband for iPad, iPhone, or iPod Touch

If you can’t hear your input signal when using the Garageband app on your iPad, iPhone, or iPod Touch, then you will need to enable the Monitor feature of the app. This feature is located in the Input Settings menu as shown in this video:

http://youtu.be/eZpFcjjv6u4?t=1m19s

 

This setting is especially important for guitar players as using Garageband’s Monitor feature enables you to hear the guitar effects built into the program. Because of this fact, this method is much preferred over utilizing the hardware monitoring feature of the Maestro app.

For more information on Apogee audio interfaces for iPad/iPhone and tutorials, check out our video page at www.apogeedigital.com/videos