ensemble thunderbolt

Are my Apogee’s outputs DC Coupled for Control Voltage (CV) use?

Control Voltage is the voltage used to control an analog circuit, like VCA’s, VCO’s all that kind of synthesizer stuff.

Note that DC coupled means there are no capacitors in the audio path of the circuit. Just because a device is DC Coupled does not automatically mean it will pass DC content. This is because there are many active ways of removing DC content. The AD16x and DA16x for instance are entirely DC coupled. But neither of them will pass DC.
The following Apogee products will pass DC to the analog output for Control Voltage:
  • Symphony I/O MkII – All modules
  • Original Symphony I/O – All modules

That’s it as of 7/1/2019

Note that the Symphony module cards are DC Coupled AND pass DC for Control Voltage on the analog outputs.

Why does my Ensemble Thunderbolt needs to be replugged every time I turn it on?

Are you powering the Ensemble On/Off just from the front power button, or cutting power completely such as via a Power Strip or Power Conditioner?

The Thunderbolt card in the Ensemble is separate from the rest of the circuitry of the Ensemble.

When you power off the Ensemble Thunderbolt via the soft button on the front, the Audio Device circuitry turns off but the Thunderbolt card remains active. This is so any other devices daisy chained to the Ensemble remain connected to the computer.

If you power off the unit by fully removing AC power, pulling the rear plug or powering off a power conditioner, you may find that afterward you need to Wake this Thunderbolt card again, by reconnecting the cable to it so the card knows to look for a computer.

 

Follow the recommended power up method here: https://knowledgebase.apogeedigital.com/ensemble-thunderbolt/power-up-order-for-ensemble-thunderbolt/

Do Apogee Thunderbolt products (Element, Ensemble Thunderbolt, Symphony I/O MkII, Thunderbridge) work with the latest 12″ MacBook?

Question:

Do Apogee’s Thunderbolt products (Element 24, Element 46, Element 88, Ensemble Thunderbolt, Symphony I/O MkII Thunderbolt, and Symphony 64 Thunderbridge) work with the 2015 and 2016 12″ MacBook?

 

Answer:

No. The 2015 and 2016 12″ MacBook, shown here, do not include a Thunderbolt port. They only have a USB-C port. The Thunderbolt 3 to Thunderbolt 2 adapters will not work with these MacBooks, despite using the same-size connectors. Apogee Thunderbolt devices will work with the 2016 MacBook Pro with Touch Bar, as discussed in this post. It should be noted that Thunderbolt 3 ports look exactly like USB-C ports and their cables also look similar. This can get a little confusing, so here are a few basic rules to help clear up any questions about connectivity:

  • USB-C and Thunderbolt 3 have the same-size port and the same-size connector for their cables. Since USB-C and Thunderbolt 3 ports look exactly the same, you will need to make sure your Mac has Thunderbolt 3 capabilities before using it with an Apogee Thunderbolt device and an Apple Thunderbolt 3 to Thunderbolt 2 adapter.
  • A Mac with Thunderbolt 3 ports, such as the 2016 MacBook Pro with Touch Bar, can use it’s Thunderbolt 3 ports to connect to any Thunderbolt 3 device, USB-C device, and Thunderbolt 2 or Thunderbolt 1 device if you use the Apple Thunderbolt 3 to Thunderbolt 2 adapter.
  • A Mac with only USB-C ports, such as the 2015 and 2016 12″ MacBook, can NOT connect to any Thunderbolt device, even when using adapters. It can connect to USB-C devices and other types of USB devices, using the proper adapters.

 

Click here for more information on the differences between USB-C ports and Thunderbolt 3 ports.

 

 

 

 

Is it ok to leave my Apogee device plugged in and connected to Mac?

Yes, it is perfectly fine for any of our devices to remain plugged in and connected to your Mac (or iOS device). There is no harm in the device remaining powered up while you’re not using it.

Signal not showing up where it’s supposed to and routing incorrect in Pro Tools

If your signal isn’t showing up correctly in Pro Tools, coming out of Pro Tools to the desired outputs, or if the routing isn’t showing up as expected, there are a few things to check. Look below for the section that applies to the Apogee product you’re using:

 

JAM, JAM 96k, MiC, MiC 96k, Groove

  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window. If you are using JAM or MiC, you will first need to create a ‘Pro Tools Aggregate I/O’ and then you will select ‘Pro Tools Aggregate I/O’ as your ‘Playback Engine’. Click here for setting up JAM for Pro Tools.  Click here for setting up MiC for Pro Tools.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

 

ONE (every model), GiO, Duet (every model), Quartet, Ensemble (every model)

  • Confirm that you are using the correct inputs/outputs on your device. Click here for instructions on how to setup ONE.  Click here for instructions on how to setup Duet.  Click here for instructions on how to setup Quartet.
  • Confirm that the device you’re using is selected as the ‘Playback Engine’ in Pro Tools by going to the the ‘Setup’ dropdown menu in Pro Tools and selecting ‘Playback Engine’. Make sure your Apogee device is selected in the ‘Playback Engine’ dropdown menu at the top of the window.
  • Launch ‘Apogee Maestro’ and click the ‘Reset Routing’ button in both the ‘Input Routing’ and ‘Output Routing’ tabs. If you’re using an Avid Duet or Avid Quartet, you will use ‘Pro Tools I/O Control’ app instead of Maestro. Click here if you need to download the Pro Tools I/O Control app for Avid Duet or Quartet.
  • You may need to reset the I/O paths in Pro Tools. This is a very common thing. Click on the ‘Setup’ menu in Pro Tools and select ‘I/O’. Once the I/O Setup opens, select all of the channels in the left-hand column and hit ‘Delete’ on your keyboard.  After you’ve deleted them, click the ‘Default’ button in the lower part of the screen. Follow the same steps for each tab in I/O Setup. Once you have gone through these steps in each tab, click the ‘OK’ button to confirm changes and exit.

Symphony I/O, Symphony I/O MkII, AD16x, DA16x, Rosetta 200, Rosetta 800

 

 

Duet, Quartet, and Ensemble Thunderbolt’s 1/4″ and XLR inputs explained

When using Duet2, Duet for iPad & Mac, Quartet, and Ensemble Thunderbolt, it is important to remember that any of the dual XLR-1/4″ combo jacks are set up so when the input is set to ‘Mic’ or ‘Line’ (+4dBu or -10dBV), only the XLR part of the jack will receive signal. This means that you will need to use an XLR cable or a cable with an XLR adapter connected to it.

The same is true in reverse- when the input is set for ‘Instrument’, only the 1/4″ part of the jack will receive signal.  This means that you will need to use a 1/4″ cable.

 

Here are some examples for setting up different types of input sources on Duet, Quartet, and Ensemble Thunderbolt:

 

Mics

Connect your Mic using only an XLR cable (no 1/4″ adapters or cables) to the XLR input jacks on your Apogee device.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘Mic’.

If you’re using a condenser mic that requires phantom power, engage the ’48′ button on the input you’re using.

Gradually bring the input level in Maestro up until you get a good level from your input source. Make sure the meter isn’t going into the red.

 

 

Guitars, Basses, Keyboards, Hi-Z Mics that have 1/4″ cables, such as harmonica mics:

Connect your Instrument using only a 1/4″ instrument cable to the 1/4″  input jacks. (be sure that you’re connecting to the 1/4″ inputs on the combo XLR-1/4″ jacks and not the 1/4″ output jacks)

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘Instrument’.

Gradually bring the input level in Maestro up until you get a good level from your input source. Make sure the meter isn’t going into the red.

 

Sending Line-Level audio to your Apogee device and bypassing it’s mic-pres

Connect the output from your line-level piece of gear (such as a compressor or external mic-pre) to the XLR input jacks. If your Line-Level device only has 1/4″ outputs, you will need to use balanced 1/4″ to male XLR cables. You can’t use the 1/4″ input jacks on your Apogee device, as they are only used for guitars/basses/keyboards.

Launch ‘Apogee Maestro’ from your Applications folder, go to the ‘Input’ tab and ‘Analog Level’ drop-down menu for whichever input you’re using to ‘+4dBu’ (for use with professional audio gear) or ‘-10dBv’ (for use with consumer audio gear).

 

What is the ‘A button’ (device ID) in Maestro for?

Most Apogee products that use the Apogee Maestro 2 control application will include a ‘Device ID’ button that can be found in multiple Maestro tabs under a graphical icon for the connected Apogee device. You will usually see this button as an ‘A’.

Here is an example of what it looks like when you have a Symphony I/O connected:

img-0

 

The purpose of this button is to quickly identify which Apogee device you’re adjusting parameters in Maestro for. When you click on the button, it will light up the front-panel of the corresponding Apogee device so you can see which device you are adjusting parameters in Maestro for. Click the button again and the device will no longer be identified.

Since multiple Apogee devices can be connected and appear in Maestro at the same time, it can sometimes be confusing to know which device you’re adjusting parameters for. Having more than one Duet or Quartet connected to a Mac may not be as common as having multiple Symphony I/Os or Ensembles connected, but the ‘Device ID’ buttons are there for each product, just in case.

 

A typical use-case:

You have 2 Symphony I/Os connected to one Mac and both are showing up in Apogee Maestro. You can go to the ‘Device Settings’ tab in Maestro and change the peripheral prefix of the 2nd Symphony I/O to ‘B’ (or any other letter you want). Now, when you click the ‘B’ button (Device ID) in Maestro, the 2nd Symphony I/O will become identified.  If you click the ‘A’ button, the 1st Symphony I/O will become identified.

 

Why are the input and output level/volume popup indicators not showing up?

Several Apogee products have pop-up level indicator graphics that will appear on the desktop of your Mac when the input and output levels are adjusted from the device or from the Mac’s keyboard volume buttons.

 

If the pop-ups aren’t appearing, there are a few things to check:

Launch ‘Apogee Maestro 2’ from your Applications folder, click on the ‘Apogee Maestro 2’ drop-down desktop menu and select ‘Preferences’. Confirm that the ‘Display pop-ups’ checkbox is checked. If you don’t see this option, then pop-ups aren’t available for the product you’re using.

 

If you’ve confirmed that the ‘Display pop-ups’ checkbox is checked and you’re still not getting the pop-ups, try the following:

 

– Unplug/replug your Apogee device

– Restart your Mac

– Launch ‘Activity Monitor’ (Applications> Utilities> ‘Activity Monitor’), click the ‘View’ drop-down desktop menu and select ‘All Processes’. Type ‘apogeepopup’ in the searchbar in the upper right-side corner of Activity Monitor. Once you see ‘ApogeePopup’ displayed in the list, highlight it and force-quit the process by clicking the ‘X’ button in the upper left-side corner of Activity Monitor. Wait a few seconds and you should see the popups again after adjusting input/output level.

 

*Note for Duet Firewire and Ensemble Firewire customers*

There was a known issue with pop-ups not working for Duet Firewire and Ensemble Firewire when using any version of Mac OS 10.8. It is recommended that you use either a version of Mac OS earlier than 10.8 or later than 10.9.