Symphony I/O

Using Legacy interfaces (AD16x, DA16x, Rosetta) with Symphony64 card or Thunderbridge

Click here to download the latest Symphony Installer package

 

To update

  1. If youʼre installing this release over a previously installed version of Symphony 64/Maestro 1, you should run the Symphony64 Uninstaller before updating to the current Symphony Release installer. If youʼre installing this release over a previously installed version of Symphony I/O software, you should run the Symphony Uninstaller included with the current Symphony Release installer package. If youʼve installed both versions, you should run both uninstallers.
  2. Double-click the Symphony System Software Installer and follow the instructions provided by the installation application.
  3. No firmware updates are required – the Symphony IO Firmware Updater is for Symphony I/O users only.
  4. You will be required to re-start your computer once installation is complete.

After updating – After updating, verify that the Symphony Source setting (found in the Maestro 2 > System Setup tab and Audio MIDI Setup) is set to the appropriate Port setting:

  • If interfaces are connected only to Port 1, set Source to Port 1 Chs 1-32.
  • If interfaces are connected to both Ports 1-2, set Source to Ports 1-2 chs 1-64.

New Features – Legacy interfaces

  • The “A” icon that previously appeared in the Apple Menu bar has been removed – Look in Maestro 2ʼs Toolbar System Status display for system information.
  • To distinguish between an AD16X and DA16X when the interface is set to Advanced routing mode or a Rosetta 800 and 200, the setting Device Type is provided in Maestro 2 (Device Settings tab). This ensures that audio paths displayed in the Input and Output Routing tabs correspond to the actual hardware I/O. If neither a 16X Series in Advanced routing nor a Rosetta is connected, the Device Type drop down is not displayed.

Known issues – Legacy DA16X Interface

  • When a single DA16X is connected in Advanced routing mode, it will initially appear as an AD16X. Simply choose DA16X under Maestro 2ʻs Device Settings > Device Type drop down menu for the interface to be correctly detected.
  • When using Symphony I/O and legacy interfaces together, Routing tabs may not display the proper number of inputs and outputs. To work around this issue, restart the computer.
  • The AD16X may initially be detected as a Rosetta 800. Workaround – restart the computer.

Using Legacy Apogee Interfaces with OS X Lion & Maestro 2

  • Note that at the current time, the use of only 1 Symphony 64 card is supported regardless of the interface connected.
  • When connecting legacy Apogee interfaces to a Symphony 64 PCIe card or Thunderbridge, ensure that the interfaces are connected in a supported hardware combination, as listed below. With a Symphony 64 PCIe card or Thunderbridge, itʼs possible to connect one supported combination to each port.
  • When connecting both Symphony I/Os and legacy Apogee interfaces to a Symphony 64 PCIe card or Thunderbridge, connect the Symphony I/O to Port 1 Channels 1-32 port and legacy interfaces (in a supported combination) to the Port 2 Channels 1-64 port.
  • Legacy Apogee interfaces donʼt include Loop clock functionality (as found on Symphony I/O). Thus, when legacy interfaces are connected to a Symphony 64 PCIe card or Thunderbridge, the “Use Loop Sync” checkbox does not appear and Loop sync functionality is defeated on the Symphony I/O. Use one of the clock configurations described on pages 6-7 of the Symphony 64 Userʼs Guide v1.1.

Legacy Interface Supported Combinations

See the Symphony 64 Userʼs Guide v1.1 for connection diagrams

1 to 4 Rosetta 800s
1 to 4 Rosetta 200s
1 AD16X (standard routing) 1 AD16X (advanced routing) 2 AD16X (standard routing) 2 AD16X (advanced routing)

1 DA16X (standard routing) 1 DA16X (advanced routing) 2 DA16X (standard routing) 2 DA16X (advanced routing)

1 AD16X (standard routing) + 1 DA16X (standard routing)
1 AD16X (standard) + 1 DA16X (standard) + 1 AD16X (standard) + 1 DA16X (standard) 1 AD16X (advanced routing) + 1 DA16X (advanced routing)

1 Rosetta 800 + 1 AD16X (standard routing) 1 Rosetta 800 + 1 AD16X (advanced routing) 1 Rosetta 800 + 1 DA16X (standard routing) 1 Rosetta 800 + 1 DA16X (advanced routing)

1 AD16X (standard routing) + 1 Rosetta 800 1 AD16X (advanced routing) + 1 Rosetta 800 1 DA16X (standard routing) + 1 Rosetta 800 1 DA16X (advanced routing) + 1 Rosetta 800

1 AD16X (standard routing) + 1 DA16X (standard routing) + 1 Rosetta 800

The Symphony I/O firmware update fails or gets stuck

Before attempting to update the Symphony I/O firmware, please follow the instructions in this link:

Updating Symphony I/O Firmware and Software

 

If the firmware update fails or stalls and never completes, quit the firmware updater app, power-cycle the Symphony I/O, and try the update again, using the following steps:

– Try connecting the Symphony I/O to a different USB hub

– Try connecting the Symphony I/O to an Apple keyboard

– Try connecting the Symphony I/O to a different USB port on your Mac

– Try the firmware update on a different Mac if you have access to one

 

You may have to try the firmware update several times before it gets through. It is not recommended to try downgrading back to the older firmware versions, as the issue with the update is not with the firmware, but with the updater app itself.

 

Is Symphony I/O compatible with Mac OS X Yosemite (10.10)?

Yes! Symphony I/O is fully compatible with Mac OS X Yosemite (10.10).  Please be sure to download and install the latest 10.10 compatible software package for Symphony from Apogee’s site.

 

Click to find the latest Symphony Software Installer

Does Symphony I/O work with versions of Pro Tools HD older than version 9?

Depending on what type of i/o modules your Symphony I/O has and what versions of firmware are loaded on it, it can work with older versions of Pro Tools HD, however we recommend using the latest Symphony I/O firmware along with version 8.1.1 or later of Pro Tools HD since the current Symphony I/O firmware is much more stable than the older versions.

If you need to use the older firmware for the Symphony I/O’s modules to emulate a Digi 192, then please read the information below carefully before requesting the older firmware from our Support department. This firmware is not available on our website.

 

The following i/o modules can be recognized as either a Digi 192 or an Avid HD I/O and can be used with versions of Pro Tools HD older than version 8.1.1 and all the way up to the current version:

– 8×8 Analog + AES I/O

– 8×8 Analog + Optical I/O

– 8×8 Analog + AES/Optical I/O

– 16 Analog Input + 16 Optical Output

– 16 Optical Input + 16 Optical Output

 

The following i/o modules can ONLY be recognized as an Avid HD I/O and can NOT be used with any version of Pro Tools HD earlier than version 8.1.1:

– 16×16 Analog In/Out

– 2×6

 

Symphony I/O doesn’t show up in Maestro and exclamation mark (!) icon stays on

If you’re having an issue getting your Symphony I/O to show up properly in Apogee Maestro and the exclamation mark (!) icon stays on the front-panel, there are a few troubleshooting steps to check, depending on what Audio Interface Mode you’re using.

 

USB Audio mode

1. Confirm that your firmware and software is up to date and that the versions match. Click here and follow these instructions.

2. Confirm that your Symphony I/O is in ‘USB Audio’ mode by pushing in and holding on the right-side front-panel encoder and scrolling through the different modes until you get to ‘USB Audio’ and then push in on the encoder again to restart the unit in ‘USB Audio’ mode.

3. Confirm that you’re using the Apogee USB cable that was included with the Symphony I/O. Unplug USB cable and then plug back in to a different port and restart your Mac.

4. Power-cycle Symphony I/O.

 

Symphony mode (Symphony 64 PCIe or Thunderbridge)

1. Confirm that your firmware and software is up to date and that the versions match. Click here and follow these instructions.

2. Confirm that your Symphony I/O is in ‘Symphony’ mode by pushing in and holding on the right-side front-panel encoder and scrolling through the different modes until you get to ‘Symphony’ and then push in on the encoder again to restart the unit in ‘Symphony’ mode.

3. Launch Audio MIDI Setup (Applications> Utilities> Audio MIDI Setup). We recommend using Audio MIDI Setup instead of System Preferences Sound. Make sure that ‘Symphony64′ (PCIe or Thunderbridge) is selected in the left-side column. In the ‘Source’ menu on the right, choose the appropriate port selection depending on how many Symphony I/Os you have. If you have 1 unit, choose ‘Port 1: 32ch’… if you have 2 units, choose ‘Ports 1-2: 64Chs’. Quit Audio MIDI Setup and restart the computer.

4. If you’ve gone through the above steps and the exclamation mark (!) icon still remains on the front-panel, there is a chance that the PC-32 port on either the Symphony I/O and/or the Symphony 64 PCIe/Thunderbridge isn’t making a complete connection and needs to be cleaned with rubbing alcohol. Follow these instructions:

Disconnect the PC-32 cable (‘Symphony’ or ‘Digi-Link’ cable) and apply some rubbing alcohol (isopropyl) to the pins on the inside of the PC-32 cable’s connector end. Make sure to apply the alcohol to the top and bottom of the pins on the connector. Now plug in and unplug the cable to the ‘Main’ port of the Symphony I/O. Do this about 20 times, so the port gets clean. Now repeat this with the Main port on the Symphony 64 PCIe or Thunderbridge. After each port has been cleaned, reconnect the PC-32 cable, power-cycle the Symphony I/O, and restart your Mac.

Level jumps when adjusting Symphony I/O’s front-panel output encoder knob

There was a known issue with some Symphony I/Os where the output level could jump by several dB when adjusting the output level with the front-panel output encoder knob.

This issue was resolved with Release 4.8 firmware and software

 

Click here to download the latest Symphony Release and follow the update instructions to ensure a successful firmware update.

 

Gain Staging – How to set proper levels with your Apogee product and recording software

Use the following steps to set input and output levels on your Apogee interface. 

Before launching your recording software:

1. Turn down the speaker/headphone output level of your Apogee interface.

2. Connect your audio source to your Apogee interface. Make sure to use the proper inputs.

• If you’re using a microphone, plug the microphone into the XLR input.

• If you’re using a guitar, bass, or other high impedance instruments, plug them into the 1/4″ instrument input.

• If you’re using an external mic-pre or another piece of line-level gear, use the XLR inputs.

Quick Tip: Some keyboards and synths can be plugged into either the Instrument or XLR inputs. You might have to experiment with what sounds better.
 

3. Launch Apogee Maestro and go to the input tab. Make the appropriate selection in the Analog Level drop-down menu for the input channel you are using.

• Microphone (Mic) – depending on the Apogee interface you are using, you would choose Ext Mic/Ext Mic 48v (ONE) or Mic (Duet, Quartet, Ensemble, SymphonyI/O with MicPre module). You will need to engage the 48v button for if you’re using a mic that requires phantom power.

• Instrument (Inst) – Guitar/Bass/some keyboards

• Line Level (+4dBu/-10dBV for balanced/unbalanced connections) – This setting is used when connecting external microphone preamps and other line-level gear.

NOTE: If you have the ONE, a line-input is accommodated by choosing Ext Mic and turning the input gain all the way down.
 

4. Set the input gain of your Apogee interface.

There are two ways you can adjust your input gain:

• By adjusting the input software encoder in Maestro

• By turning the physical knob (encoder) on your Apogee interface (make sure you’ve set the knob to control the input channel and not the output level. See your User’s Guide for more information on setting this).

Quick Tip: Ideally, the level in the input meter should be as high as you can get it without hitting an “over”. If you see red in the meter, you know you need to turn the input gain down. In some cases you may need to adjust the output of the audio source you are using. You may need to move your microphone closer to the sound source or further away. You may need to turn the level of your guitar or keyboard up or down.
 

Launch your recording software, create an audio track, and put the track into input or record mode. It is a good idea to leave the fader of the track you are recording and any Master Fader for the mix set at their default setting.

5. Adjust the output level of your Apogee interface.

• Gradually increase the output level of your Apogee interface so you can hear what your input source sounds like in the speakers or headphones.

• After you get the output set to a comfortable listening level, listen for any distortion in the input audio.

• If the audio sounds bad, you may have something set wrong. Go through steps 2, 3, and 4 to trouble-shoot the problem.

Note: Two common issues are that the sound is too quiet or that it’s distorted. It may be a simple case of needing to turn the input gain up and the output level down or the input gain down and the output level up.

¿Los productos de Apogee son compatibles con Pro Tools 11?

No anticipamos ningún problema y esperamos anunciar compatibilidad total para todos los productos de Apogee en las próximas semanas. Sin embargo, no podemos confirmar oficialmente total compatibilidad Apogee con Avid Pro Tools 11 hasta que el software este disponible y ha sido completamente probado. Por favor, visite nuestro sitio web para obtener la última información de compatibilidad. Si ya eres dueño de un producto Apogee, registralo yendo a: http://www.apogeedigital.com/support.php Usted recibirá una notificación de actualización por correo electrónico.

Will Apogee USB interfaces work with USB 3.0 ports on my Mac?

Yes, Apogee interfaces including JAM, JAM 96k, MiC, MiC 96k, GiO, Groove, Duet 2, Duet for iPad & Mac, ONE, ONE for iPad & Mac, Quartet, and Symphony I/O have been tested and work well with USB 3.0 ports.

Note-

Although Symphony I/O works as an audio interface with USB 3.0 ports, you will need to use a USB 2.0 port or a USB hub to run the Symphony I/O firmware updater.

How to do parallel drum compression in Logic?

Part 1

 

Part 2